Pulse X BF Squonk Kit by Vandy Vape & Tony B

Color: Frosted Black


Pulse X BF Squonk Kit by Vandy Vape & Tony B Kit Overview

With upgraded firmware and the capacity for a high amp 21700 battery comes the improved Pulse X BF Squonk Kit by Vandy Vape and Tony B. The regulated Pulse X mod included with this kit has utilitarian dimensions of 82.6mm x 54.8mm x 27mm and a conveniently lightweight. The exterior of the mod utilizes Vandy Vapes replaceable magnetic panels that come in a variety of translucent colors to give your kit a touch of personality. The front panel leaves an opening for access to the internal easy grip squonk bottle with a massive 8mL e-liquid capacity. Along one side of this device is a three-button interface with a power button and up/down buttons to control a large OLED display screen. You can not only adjust the brightness of this display screen to cooperate with your environment, but you can also put the device into stealth mode, making the screen black while its still on, by pressing all three buttons at the same time. Through the implementation of the intelligent Vandy Chip, this screen displays all the pertinent vaping data you can imagine. The Vandy Chip gives you precise output control over several different modes including Temperature Control, Variable Wattage, Voltage, Bypass, Boost, and other DIY settings. Temperature Control can range from the industry standard 200-600F (100-315C) within atomizer resistances of 0.05-1.5 ohm. Variable Wattage mode starts at 5W and can go all the way up to 90W within atomizer resistances of 0.05-3.0 ohm with the use of a 21700 battery. Other modes offered include Variable Voltage of 0.5-8.5V, Boost mode in which you can operate at Normal or Hard, NLS (No Lift Shift), RST to return to the original factory settings, and custom curves. You can also set the amount of time you want to go by before your device automatically goes into sleep mode. On the display screen is a battery life indicator that will indicate battery life with the use of a single 18650, 20700, or 21700 battery. For you convenience, Vandy Vape and Tony B have included an 18650 battery adaptor sleeve. Inside the chassis of the Pulse X Mod are positive and negative signs to indicate which way to install your battery. To charge whichever battery you decide to use and upgrade firmware as it becomes available, Vandy Vape has given the Pulse X Regulated Mod a Micro-USB port underneath the up/down buttons. Safety features of this mod include overheating protection, over-current protection, open circuit protection, and overtime protection.

Just as Vandy Vape and Tony B upgraded their Pulse Mod, they also upgraded their atomizer to optimize your experience by releasing the Pulse X BF RDA. Co-designed by Tony B and founder of Vandy Vape, Stefen Z, this RDA is capable of single and dual coil builds in both horizontal and vertical orientations. The Pulse X RDA has either a frosted or superior Stainless Steel frame held on by two strong o-rings and consisting of six small airflow holes on both sides. The adjustable cap can close the top three holes, the bottom three holes, or two vertical airflow holes at a time while sending air downward directly to your coils. The X in the name of this tank comes from the overall look of the build deck that consists of positive and negative components separated by a PEEK insulator. For versatility, this tank comes with a standard 510 contact pin as well as a 510 squonk pin that allows e-juice to come up through a one way valve that lets excess juice return to the bottle in the Pulse X Mod. Your e-liquid is sent up to the top of the build deck where it then shoots downward onto your coils and Cotton like water from a showerhead. The build deck is equipped with an extremely deep juice well to keep your Cotton fully saturated from top to bottom. For non-squonk use, you can also fill this tank through the mouthpiece like a typical drip atomizer if you desire to do so. The Vandy Chip within the Pulse X Mod has a rapid firing time so you can enjoy each draw immediately. Vandy Vape has made an optional matching Silicone bottle with a 30mL e-liquid capacity and both a 510 cap and squonk cap so you can keep your liquids flowing. Keep up with the latest in rebuildables and get your Pulse X BF Squonk Kit by Vandy Vape and Tony B today.

Pulse X BF Squonk Kit by Vandy Vape & Tony B Features

  • Dimensions: 27 x 54.8 x 82.6mm (D x W x H)
  • Construction: Nylon, Heat-Resistant ABS 
  • Powered By Vandy Chipset
  • Output Mode: VT-Ti / VT-Ni / VT-SS / VW / VV / Bypass 
  • Output Wattage: 5 - 90W
  • Output Voltage: 0.5 - 8.5V
  • Resistance Range (TC): 0.05 - 1.5 ohm
  • Resistance Range (VW): 0.05 - 3.0 ohm
  • 510 Threading
  • Spring Loaded 510 Connector Pin
  • Temperature Range: 200 - 600°F (100 - 315°C)
  • OLED Display Screen
  • Battery: 1 x 18650 / 20700 / 21700 (Not Included)
  • Replaceable Magnetic Panels
  • Atomizer Capacity: 2ml
  • Squonk Bottle Capacity: 8ml
  • Top and Bottom Refill Support 
  • Airflow: Side Adjustable
  • Safety Features: Overheat Protection / Open Circuit Protection / Short Circuit Protection / Overcurrent Protection / Overtime Protection / Low-Battery Warning

Pulse X BF Squonk Kit by Vandy Vape & Tony B Content

  • 1 x Pulse BF Box Mod
  • 1 x Pulse 24 BF RDA Special Edition
  • 1 x 18650 Battery Adapter
  • 1 x 16mm Derlin Drip Tip
  • 1 x Accessory Bag

Payment & Security


Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Estimate shipping

You may also like

Recently viewed